PMD
Multi-Function Cutter
List 53400 - PHOENIX® PMD: SA List 78234 - PHOENIX® PMD: SS List 52606 - PHOENIX® PMD: ASF List 78334 - PHOENIX® PMD: SF
Side Milling & Slotting
Side Milling Aa: 0.393" • Ar: 0.2D
Face Milling Aa: 0.118" • Ar: 1.0D
Tensile Strength - Hardness
Work Material
Cutting Speed Vc (SFM)
Feed per Tooth fz (in/t)
Cutting Speed Vc (SFM)
Feed per Tooth fz (in/t)
Mild Steels, Carbon Steels (1010, 1018) Carbon Steels, Alloy Steels (1050, 4140)
590 (330 - 820) 590 (330 - 820) 495 (260 - 655) 495 (260 - 655) 260 (195 - 395) 590 (330 - 985) 590 (330 - 820) 985 (655 - 4920) 115 (85 - 195) 130 (100 - 395) 330 (130 - 495) 260 (130 - 395)
0.010 (0.008 - 0.020) 0.008 (0.006 - 0.016) 0.008 (0.006 - 0.016) 0.007 (0.006 - 0.016) 0.007 (0.006 - 0.016) 0.010 (0.006 - 0.020) 0.006 (0.004 - 0.016) 0.012 (0.008 - 0.020) 0.006 (0.004 - 0.012) 0.007 (0.004 - 0.014) 0.007 (0.004 - 0.012) 0.005 (0.003 - 0.008)
590 (330 - 820) 590 (330 - 820) 495 (260 - 655) 495 (260 - 655) 260 (195 - 395) 590 (330 - 985) 590 (330 - 820) 985 (655 - 4920) 115 (85 - 195) 130 (100 - 395) 295 (130 - 495) 230 (130 - 395)
0.005 (0.002 - 0.008) 0.004 (0.002 - 0.008) 0.004 (0.002 - 0.007) 0.004 (0.002 - 0.007) 0.004 (0.002 - 0.007) 0.005 (0.002 - 0.008) 0.005 (0.002 - 0.008) 0.006 (0.004 - 0.010) 0.004 (0.002 - 0.006) 0.004 (0.003 - 0.010) 0.004 (0.003 - 0.008) 0.003 (0.002 - 0.006)
~180 HB
P
~280 HB
Die Steels (D2, H13)
~280 HB
Stainless Steels (Dry) (304, 420) Stainless Steels (Wet) (304, 420)
~250 HB
M
~250 HB
Cast Iron (FC250)
~350 N/mm²
K
Ductile Cast Iron (60-40-18) Aluminum Alloys (6061, 7075)
~800 N/mm²
N
~13% Si
Heat Resistant Alloys (Inconel 718)
-
S
Titanium Alloy (Ti-6Al-4V)
-
Pre-hardened Steel (P20, Stavax) Die Cast Steels (A2, S7) Hardened Steels (D2)
40 - 43 HrC
H
43 - 48 HrC
50 - 55 HrC 0.002 (0.002 - 0.004) 1. Above recommended Cutting Speed is for short shank type; for long shank type, use 80% of the Cutting Speed shown in the above table. 195 (130 - 295) 0.004 (0.002 - 0.008) 165 (130 - 295)
osgtool.com
1532
End Mill Technical
Powered by FlippingBook