AE-VMFE & AE-CR-VMFE
Advanced Performance Anti-Vibration Reduced Shank Carbide End Mills
List 8245 - A Brand AE-VMFE: SQ, 4 Flute List 8246 - A Brand AE-CR-VMFE: CR, 4 Flute
Side Milling
Hardness
–
Up to 30 HRC
–
–
–
–
30-45 HRC
Mild Steels Carbon Steels Cast Iron
Prehardened Steels Hardened Steels
Work Material
Tool Steel Alloy Steel
Precipitation Stainless Steel
Ni-Based Alloy Inconel 718
Stainless Steel
Titanium Alloy
Cutting Speed 330-460 SFM 330-460 SFM 330-460 SFM 330-430 SFM 300-400 SFM 200-260 SFM 330-460 SFM
a a=2.0D a r=0.1D
Depth of Cut
Mill Dia. (Inch)
Speed RPM
Feed in/min
Speed RPM
Feed in/min
Speed RPM
Feed in/min
Speed RPM
Feed in/min
Speed RPM
Feed in/min
Speed RPM
Feed in/min
Speed RPM
Feed in/min
6.0 8.0
6,392 4,794 3,835 3,196
99.7 74.8 59.8 49.9
6,392 4,794 3,835 3,196
89.5 67.1 53.7 44.7
6,392 4,794 3,835 3,196
76.7 57.5 46.0 38.4
6149 4612 3690 3075
64.0 48.0 38.4 32.0
5664 4248 3398 2832
54.4 40.8 32.6 27.2
3722 2791 2233 1861
31.3 23.4 18.8 15.6
6,392 4,794 3,835 3,196
81.8 61.4 49.1 40.9
10.0 12.0
1. The above milling condition is a guidline for overhang length 5xD. 2. Use a rigid and precise machine and holder. 3. Please use a suitable fluid with high smoke retardant properties.
4. During dry (no fluid) milling, please use air blow to remove chips from the milling area and to eliminate chip packing. 5. Please use water-soluble coolant when machining stainless steel, precipitation stainless steel, titanium alloy, Ni-based alloy. 6. Reduce speed and feed as well as depth of cut when high precision is required. 7. Adjust the speed and feed accordingly when the overhang length is longer than specified (refer to Parameter Reduction Chart below).
Parameter Reduction Chart by Length to Diameter Ratio
Hardness
–
Up to 30 HRC
–
–
–
–
30-45 HRC
Prehardened Steels Hardened Steels
Mild Steels Carbon Steels Cast Iron
Tool Steel Alloy Steel
Precipitation Stainless Steel
Ni-Based Alloy Inconel 718
Work Material
Stainless Steel
Titanium Alloy
Depth of Cut Speed RPM Aa Ar
Feed in/min
Speed RPM
Feed in/min
Speed RPM
Feed in/min
Speed RPM
Feed in/min
Speed RPM
Feed in/min
Speed RPM
Feed in/min
Speed RPM
Feed in/min
L/D
6 1.7D 0.08D 7 1.6D 0.05D 8 1.5D 0.03D
80% 65% 50%
80% 65% 50%
80% 65% 40%
80% 65% 40%
80% 65% 30%
80% 65% 30%
80% 65% 40%
Side Milling
osgtool.com
1344
End Mill Technical
Powered by FlippingBook