SF
Screw Fit End Mill
List 78016 OSG PHOENIX® PSE SF, Screw Fit Head
SPEED FEED 1529
PACKED 1 PIECE
ARBORS 1295-1298
ACCS. 1216
INSERTS 1213-1215
STEEL
L
Pilot Diameter
Thread Size
Flange Diameter
Overall Length Spanner Wrench
Diameter
Number of Flutes
Applicable Insert
EDP Number
Designation
D (mm)
Da (mm) 6.50 6.50 8.50 8.50 8.50 8.50
Dg (mm)
D2 (mm) 9.00
L (mm)
7803822 7803823 7801600 7803824 7801612 7801613 7801601 7803825 7801614 7801615 7801607 7801602 7803826 7801618 7801616 7801608 7801603 7801609 7801604 7803827 7801617 7801619 7801610 7801605 7801611 7801606
PSE07R010SF6-2 PSE07R012SF6-3 PSE11R016SF8-2 PSE07R016SF8-4 PSE11R017SF8-2 PSE11R018SF8-2 PSE11R020SF10-3 PSE07R020SF10-4 PSE11R021SF10-3 PSE11R022SF10-3 PSE15R025SF12-2 PSE11R025SF12-4 PSE07R025SF12-5 PSE15R026SF12-2 PSE11R026SF12-3 PSE15R028SF12-2 PSE11R028SF12-4 PSE15R032SF16-3 PSE11R032SF16-5 PSE07R032SF17-6 PSE11R033SF16-3 PSE15R033SF16-3 PSE15R035SF16-3 PSE11R035SF16-5 PSE15R040SF16-4 PSE11R040SF16-6
10.00 12.00 16.00 16.00 17.00 18.00 20.00 20.00 21.00 22.00 25.00 25.00 25.00 26.00 26.00 28.00 28.00 32.00 32.00 32.00 33.00 33.00 35.00 35.00 40.00 40.00
2 3 2 4 2 2 3 4 3 3 2 4 5 2 3 2 4 3 5 6 3 3 3 5 4 6
M6 M6 M8 M8 M8 M8
26.00 26.00 27.00 27.00 27.00 27.00 33.00 33.00 33.00 33.00 35.00 35.00 35.00 35.00 35.00 35.00 35.00 40.00 40.00 35.00 40.00 40.00 40.00 40.00 40.00 40.00
7 7
ZDKT07 ZDKT07 ZD_T11 ZDKT07 ZD_T11 ZD_T11 ZD_T11 ZDKT07 ZD_T11 ZD_T11 ZDKT15 ZD_T11 ZDKT07 ZDKT15 ZD_T11 ZDKT15 ZD_T11 ZDKT15 ZD_T11 ZDKT07 ZD_T11 ZDKT15 ZDKT15 ZD_T11 ZDKT15 ZD_T11
11.00 14.50 14.50 14.50 14.50 18.00 18.00 18.00 18.00 23.00 23.00 23.00 23.00 23.00 23.00 23.00 28.00 28.00 28.00 28.00 28.00 28.00 28.00 28.00 28.00
10 10 10 10 14 14 14 14 17 17 17 17 17 17 17 22 22 22 22 22 22 22 22 22
10.50 10.50 10.50 10.50 12.50 12.50 12.50 12.50 12.50 12.50 12.50 17.00 17.00 17.00 17.00 17.00 17.00 17.00 17.00 17.00
M10 M10 M10 M10 M12 M12 M12 M12 M12 M12 M12 M16 M16 M16 M16 M16 M16 M16 M16 M16
Stocked Globally Stocked Note: When using an insert with a corner radius of R2 or greater, the corner of the cutter body must be corrected. The body corner radius should equal insert radius minus one (example: if insert radius is R3, body radius should be R2). Available Upon Request; MOQ May Apply
DESIGNATION EXPLANATION PSE 11 R 016 SF 8-2
Thread Size
Series
Insert Size
Cutting Direction
Diameter
Body Type
Number of Flutes
See Full Detail on Page 1524
P
M
K
N
S
H
Steel
Stainless Steel
Cast Iron
Non-Ferrous
HRSA
Hardened Steel
Material recommendation based on inserts compatible with this tool body.
Good
Best
osgtool.com
1286
Indexables
Powered by FlippingBook