PSEL Rough Milling Cutter
List 53000 OSG PHOENIX® PSEL SA/FA
SPEED FEED 1530
PACKED 1 PIECE
ACCS. 1224
INSERTS 1221-1223
STEEL
Length of Cut
Neck Length
Overall Length
Shank Dia. Applicable Insert
Number of Inserts per Flute
Total Number of Inserts
Dia. Number of Flutes D (Inch)
EDP Number
Designation
Body Type Type
Lc (Inch)
L1 (Inch)
L (Inch)
d (Inch)
53000000 PSEL11R100SA100-2-27 Cylindrical Shank 1 1.000 2
3 4 5 4 5 3 3 4 5 4 5 3
6 8
1.063 1.968 4.921 1.000 ZD_T11 1.457 2.362 5.512 1.250 ZD_T11
53000001 53000002 53000003 53000004 53000005 53000006 53000007 53000008 53000009 53000010 53000011
PSEL11R125SA125-2-37 Cylindrical Shank 1 1.250 2 PSEL11R125SA125-3-45 Cylindrical Shank 1 1.250 3 PSEL11R150SA125-3-37 Cylindrical Shank 2 1.500 3 PSEL11R150SA125-4-45 Cylindrical Shank 2 1.500 4 PSEL15R150SA125-2-38 Cylindrical Shank 2 1.500 2 PSEL11R100FA100-2-27 Weldon Shank 1 1.000 2 PSEL11R125FA125-2-37 Weldon Shank 1 1.250 2 PSEL11R125FA125-3-45 Weldon Shank 1 1.250 3 PSEL11R150FA125-3-37 Weldon Shank 2 1.500 3 PSEL11R150FA125-4-45 Weldon Shank 2 1.500 4 PSEL15R150FA125-2-38 Weldon Shank 2 1.500 2
15 1.791 2.362 5.512 1.250 ZD_T11 12 1.457 2.362 5.512 1.250 ZD_T11 20 1.791 2.362 5.512 1.250 ZD_T11
6 6 8
1.496 2.362 5.512 1.250 ZDKT15 1.063 1.968 4.248 1.000 ZD_T11 1.457 2.362 4.642 1.250 ZD_T11
15 1.791 2.362 4.642 1.250 ZD_T11 12 1.457 2.362 4.642 1.250 ZD_T11 20 1.791 2.362 4.642 1.250 ZD_T11 1.496 2.362 4.642 1.250 ZDKT15 6
Stocked Globally Stocked Note: When using an insert with a corner radius of R2 or greater, the corner of the cutter body must be corrected. The body corner radius should equal insert radius minus one (example: if insert radius is R3, body radius should be R2). Available Upon Request; MOQ May Apply
Type 1
Type 2
Lc
Lc
L1
L1
L
L
With coolant hole.
With coolant hole.
DESIGNATION EXPLANATION PSEL 11 R 100 SA 100-2-27
Shank Diameter
Series
Insert Size
Cutting Direction
Diameter
Body Type
Number of Flutes
Length of Cut
See Full Detail on Page 1524
P
M
K
N
S
H
Steel
Stainless Steel
Cast Iron
Non-Ferrous
HRSA
Hardened Steel
Material recommendation based on inserts compatible with this tool body.
Good
Best
osgtool.com
1217
Indexables
Powered by FlippingBook