PHX Phoenix Deep Feed Radius End Mill
List 9580 (Continued) EXOPRO® PHX-PC-DFR, Pencil Neck, Deep Feed
SPEED FEED 1432-1433
PACKED 1 PIECE
h6 SHANK
STUB
CARBIDE WXS
55˚
3 FLUTE
Neck Diameter Min
Neck Diameter Max
Effective Draft Angle
Neck Draft Angle
Corner Radius
Length of Cut
Neck Length
Overall Length
Shank Diameter
Diameter
EDP Number
Type
D (mm) 8.00 8.00 8.00 8.00 8.00
R (mm) 2.00 2.00 2.00 2.00 2.00 2.00 2.00 2.00 2.00 2.00 2.00 2.00 2.00 2.00 2.00 2.00 2.00 2.00 2.00 2.00 2.00 2.00
Lc (mm)
L1 (mm)
d1 Min (mm)
d1 Max (mm)
α ( ˚ )
β ( ˚ )
L (mm)
d (mm)
3097862 3097826 3097842 3097853 3097844 3098041 3098051 3098061 3098026 3098042 3098043 3098044 3098053 3098045 3098046 3098064 3098241 3098224 3098242 3098243 3098244 3098254
12.00 12.00 12.00 12.00 12.00 15.00 15.00 15.00 15.00 15.00 15.00 15.00 15.00 15.00 15.00 15.00 18.00 18.00 18.00 18.00 18.00 18.00
63.30 80.00 63.30 82.40
7.90 7.90 7.90 7.90 7.90 9.90 9.90 9.90 9.90 9.90 9.90 9.90 9.90 9.90 9.90 9.90
12.00
2.00 0.40 1.00 1.50 1.00 1.00 1.50 2.00 0.40 0.80 0.84 0.87 1.50 0.88 0.90 2.00 0.67 0.41 0.81 1.00 0.88 1.50
2.00 0.50 1.00 1.50 1.00 1.00 1.50 2.00 0.50 1.00 1.00 1.00 1.50 1.00 1.00 2.00 1.00 0.50 1.00 1.00 1.00 1.50
120.00 12.00 150.00 10.00 150.00 10.00 150.00 12.00 180.00 12.00 120.00 12.00 120.00 12.00 120.00 12.00 150.00 12.00 160.00 16.00 160.00 16.00 180.00 16.00 180.00 16.00 200.00 16.00 220.00 16.00 220.00 16.00 120.00 16.00 180.00 16.00 180.00 16.00 180.00 16.00 220.00 20.00 220.00 20.00
2 1 2 2 2 2 2 2 1 1 1 1 2 1 1 2 1 1 1 2 1 2
9.09
10.00 12.00 12.00 12.00 12.00 12.00 11.38 12.17 12.87 13.57 16.00 14.26 14.96 16.00
120.60 64.30 45.20 35.60 100.00 80.00 100.00 120.00 121.60 140.00 160.00 92.90 60.00
10.00 10.00 10.00 10.00 10.00 10.00 10.00 10.00 10.00 10.00 10.00 12.00 12.00 12.00 12.00 12.00 12.00
11.90 13.37
120.00 11.90 13.68 100.00 11.90 14.76 122.60 11.90 16.00 160.00 11.90 16.86 160.80 11.90 20.00
Globally Stocked
Stocked
Available Upon Request; MOQ May Apply
EP
Type 1
Type 2
15˚
Lc
Lc
L1
L1
L
L
Effective Draft Angle
Effective Draft Angle
* The tool may deflect and interfere with the draft area depending on the milling condition. * For convenience, the Neck Draft Angle (β°) is shown the same as the Effective Draft Angle (α°), but actually it is different. (It does not interfere with the Effective Draft Angle (α°)
α°
α°
Neck Draft Angle β°
Neck Draft Angle
β°
P
M
K
N
S
H
Steel
Non-Ferrous
HRSA
Carbon Steel
Stainless Steel
Hardened Steel
Alloy Steel 4140 4340
Cast Iron
Aluminum Nickel Alloy Titanium
Die Steel
Low Medium High 1010 1018 1035 1045 1065
6Al4V (30 HRC)
~35 HRC
35-45 HRC
45-50 HRC
50-70 HRC
6061 7075 Casting Inconel
300
400 17-4 PH
Good
Best
osgtool.com
1007
Corner Radius
Powered by FlippingBook