U-WAVE Wireless Wireless Data Collection System
U-WAVE-T
• The system using our proprietary communication method features stable communication and low power consumption, resulting in improved work efficiency.
• It can be connected to various types of tools using optional special connection cables.
A
• Data format Example of format when the Digimatic gage displays 12.34 DT1 01 02 +00000012.34 M
U-WAVE-T (IP67 type)
U-WAVE-T (buzzer type)
Model
Order No.*
02AZD730G
02AZD880G
Protection Rating
IP67 LEDs
None
Header
Unit M: mm
Data reception indication
Buzzer and LEDs
Digimatic gage display value* 1
DT1: Measurement data ST1: Status code* 2
U-WAVE-TM / TC / T ID: 00 to 99 U-WAVE-R ID: 00 to 99 *1 Data interface function is switchable to “Measurement value only” e.g.) 12.34 *2 Example of status code format
Power source
Lithium battery CR2032×1 Approx. 400,000 transmissions
Battery life
Dimensions (mm)
44×29.6×18.5
Mass (g) 23 * To use this product, conformity to the applicable radio law in each country is required. Code number differs depending on the destination country. Please contact your nearest M³ Solution Center.
ST1 01 02 0999999073 99
U-WAVE-T system configuration
Device ID* 3
Header
Status code
Receipt of data can be checked by buzzer and LED (common specification)
LED (OK: Green, NG: Red)
U-WAVE-TM / TC / T ID 99: Data cancellation U-WAVE-R ID 01: No response from Digimatic gage 03: Measurement data missing, others
Status code
LED (OK: Green, NG: Red)
*3 Unique number assigned to U-WAVE at shipment
U-WAVE-T (buzzer type)
Notes on Identification of Measurement Data and Multiple Systems Operation Following the above format, the U-WAVE data format starts with a 4-digit code where the first two digits represent receiver channels and the last two are transmitter channels. The large number of transmitter/ receiver combinations possible with this scheme ensures that the receivers in a factory measurement system only accept data from the intended transmitters, even when several receivers are all within communication range of different transmitters using the same channel. Different frequency bands (up to 15 available) may also be used to further ensure that there are no communication problems between adjacent U-WAVE-R units. U-WAVE-T (U-WAVE fit) System Communication Specifications • Wireless communication Wireless specifications Original <based on IEEE802.15.4 (2.4 GHz)> Wireless communication distance Approx. 20 m (line of sight) Wireless communication speed 250 kbps Transmission output 0 mW (1 dBm) or less Modulation method DS-SS (Direct Sequence - Spread Spectrum) Resistant to interfering signals and noise Communication frequency 2.405 to 2.475 GHz
(IP67 type)
Highly resistant to dust and water ingress
U-WAVE-R
U-WAVE-T dedicated connection cable
A dedicated cable connects a Digimatic gage to U-WAVE-T . Check the connector (A to G, SA and SF) compatible with the Digimatic gage to be used and
select either standard type (figure 1) or foot switch type (figure 2) according to your application. Refer to Pages A-28 through A-30 for connector tool type.
Standard connection cable Connection cable for foot switch Order No. Order No.
Type
02AZD790A 02AZD790B 02AZD790C 02AZD790D 02AZD790E 02AZD790F 02AZD790G 02AZF960 02AZG011
02AZE140A 02AZE140B 02AZE140C 02AZE140D 02AZE140E 02AZE140F 02AZE140G 02AZF960 02AZG021
(A) Water-proof model with output button (B) Water-proof model with output button
(C) With data-out button (D) 10-pin plain type (E) 6-pin round type (F) Plain type straight
(G) Plain type straight water-proof model
(SA) Water-proof straight model with data output button
(SF) Straight standard type
Application example of the clip
Standard accessory clip for cable fixing
9 types of connector
(A)
(E)
160 mm
15 channels (2.405 to 2.475 GHz at intervals of 5 MHz) The noise search function avoids interference with other communication devices.
Used band
(F)
To U-WAVE-T unit
Figure 1. Standard type connection cable
To measuring tool
(B)
Foot switch (optional) 937179T 測定器側
(G)
U-WAVE-T 側
Approx. 500 mm
(C)
(SA)
Connector attached to U-WAVE-T by 2 screws
Approx. 80 mm
Approx. 80 mm
(D)
(SF)
To U-WAVE-T unit
To measuring tool
Figure 2. Connection cable for foot switch
A-19
Powered by FlippingBook